So here is the problem. The LCD on my Yamaha DX11 synthesizer has faded so much that I can barely see what instrument I am playing - as you can see in the photo above. It appears that the seals around the edge of the glass panel have failed, because the fading started at the outside edges and has progressed inwards. When switched off the LCD is a peculiar pink colour, which you can see in the photo below. The old LCD is on the right, a new one on the left. (Note that I have already transferred the plastic bezel from the old LCD to the new one - it is held in place by a double-sided adhesive strip).
But where do you get replacement parts for an instrument which is probably over 30 years old?
I opened up the the synth and measured the size of the thing and then trawled through catalogues looking for similar devices. I found the Displaytech 162B-BC-BC looked to be the right shape and size, and the row of pins was in the same position along the bottom edge. The Displaytech part has 16 pins instead of 14, but I could see from the datasheet that pins 1 and 2 were connected to the backlight. It was readily available from RS Components at £7.94 (Part number 532-6379) so I ordered one.
While I waited for it to arrive I found the Service Manual for the DX11 on line, and that confirmed that, apart from the two extra pins for the LED backlight, the connections were exactly the same on the two displays.
I had to extend the wires on the LED backlight, and my attempts at desoldering the 14-pin header on the old display were unsuccessful, so I cut the wires one by one, and soldered them to the new display module. The wiring between the connector and the module is 1 to 1, but since the wires are not colour-coded (except for pin 1), it is wise to move them one at a time. In the picture below, you can see the LCD module, nestling in the middle, between the larger PCBs. It is held in place by a metal surround which is secured by a single screw.
This picture shows the two modules side, by side, before I transferred the wires, so the old one is on the right and the new one on the left.
The picture below shows the new module in position, with the metal surround back in in place and the LED backlight lead waiting to be connected back in the socket on the main board.
It was a great delight to see the new panel light up with nice clear text. I was expecting to have to make some adjustment to the contrast control resistor, but this was not necessary. The Displaytech module seems to be electrically very similar - even the character fonts seem to be equivalent. A thin metalic strip of the bezel is visible at the top and bottom of the LCD window, and it might be nice to black that out with a strip of black tape or even marker pen. But I couldn't be bothered to take it all apart again.
Happy Christmas and 73 to you all.
Hugh M0WYE
Sunday 27 December 2015
Sunday 13 December 2015
Apparatus for the Testing of Christmas Tree Light Bulbs
Apparatus for the testing of Christmas-tree light bulbs. I got very frustrated trying to test Christmas-tree light bulbs using a multimeter. Almost impossible to hold the probes on the little wires. I thought about making some kind of bulb-holder, but then hit upon this idea, using a wooden clothes peg.
Copper tape is wrapped around the ends of the arms and secured with a soldered joint on the outside of the peg. Wires are attached and connected to a battery which can be conveniently carried in a pocket.
The peg is clipped across each bulb as it is removed from the chain. The battery should be chosen appropriate to the Voltage rating of the bulbs - mine are 2.4V - so a part-used "C" cell makes the bulb glow dimly, Note small screw positioned between arms of peg to prevent it closing fully, this is important as it prevents the battery being shorted when no bulb is present.
Even though it was dark by the time I had finished it, I was still able to get the set working. The wires on some of the bulbs had become tarnished and so there were multiple"failures" within each series string of bulb. The tarnish seems to be due to age rather than moisture as the new bulbs in the pack had also gone the same way. Happily a little scraping with a craft knife soon got them going again.
Happy Christmas and 73 to you all.
Hugh M0WYE